+92 333 321 7076

Mon To Sat - 9AM TO 7PM



TDS Meter Water Testing


A TDS meter is a small hand-held device used to indicate the Total Dissolved Solids in a solution, usually water. Since dissolved ionized solids, such as salts and minerals, increase the conductivity of a solution, a TDS meter measures the conductivity of the solution and estimates the TDS from that reading.


First, it’s important to know what TDS really is: Total Dissolved Solids. After water falls to the ground as rain, it dissolves the minerals present in the rocks and soil it passes over or through. As it dissolves these minerals, they remain in the water at varying levels of concentration. This is a very natural process and it helps make water taste “right” by slightly raising the pH of the water. The most common minerals found in water are Calcium, Magnesium, and Sodium.
Some areas of the country have higher levels of these dissolved minerals in their water making it “hard” and other areas have lower levels. Anything under 200 mg/L (or ppm) is good and 100 mg/L is considered excellent. As the TDS level goes below this level (as the minerals are removed) the water has a lower pH and becomes more acidic or corrosive. This causes a noticeable difference in the taste of the water. TDS levels over 400 mg/L are considered non-potable (don’t drink that stuff).
Knowing your TDS level is important when considering a water softener for your home. Water softeners can protect pipes and plumbing, decrease spots and stains on dishes and shower doors, increase the life of brighter clothing, and more. Keep in mind a water filter is not a water softener. The ultimate goal of a water filter is not to remove all solids in the water. Keep in mind a water filter is not a water softener. The ultimate goal of a water filter is not to remove all solids in the water.


A TDS meter does not measure contaminants. It will not tell you if your water is healthy. Some healthy minerals like potassium, magnesium, and calcium can actually cause your TDS meter to spike.  So, any water filter with a remineralizer will cause the opposite effect on a TDS meter than you expect. Your water could also have heavy metals like lead, or other contaminants like pesticides, pharmaceuitcals, or hexavalent chromium. The TDS meter will not pick these contaminants up.

TDS Meter Clarification

When considering water filtration, the short answer is: no – you do not need a TDS meter. Having your water tested using a test kit will provide a report that explains exactly what’s in the water – including those dissolved solids. You’ll find out what contaminants are in your water those causes you concern, and then you can find a filtration solution to meet all of your water goals.


One of the reasons Aqua Shield filtered water tastes so good is because we utilize a selective filtration process. All of our drinking water filters use the same process and we call that the Aqua Shield Filtration Technology. Our filter is certified to remove 77 contaminants including chlorine, chloramines, lead, pharmaceuticals, pesticides, herbicides, etc.
However, we specifically DO NOT remove the healthy minerals (calcium, magnesium, and potassium) in the water. We filter out the bad but leave in the good – and some of what makes it good are those TDS’s. The Aqua Shield selective filtration process will make water taste more natural because we filter water back to the form nature intended.
The Aqua Shield Filtration Technology utilizes three main processes.  First, carbon absorption – this removes most of the organic compounds (chlorine, pharma, pesticides, herbicides, etc). The body is mostly carbon, so this filtration process acts much like the human body would. Our filtration process here is better than gravity pitchers because we use a dense carbon block and pressure instead of granulated carbon and gravity. The result is much greater contact time of the water with the carbon even though the filtration process is faster. Cool, huh?
Second, mechanical filtration – this removes particles larger than 0.5 microns such as giardia or cryptosporidium (which are chlorine resistant parasites). This kind of filtration doesn’t come from most gravity filtration products, either. This only happens with extremely slow filtration or by utilizing pressure. Last, ion exchange – this is how heavy metals like lead and mercury are filtered. Basically, we have a potassium ion mixed with the carbon which is designed to grab any particles with a positive charge (i.e. heavy metals) and replace those particles with potassium. This filtration process can actually result in a small increase in TDS concentration.
All that said, there are some dissolved solids that should not be in drinking water. They are very rare in tap water, but things like arsenic can find its way into tap water at low levels of concentration. The local water suppliers are required to do a water quality test and make the results public. If there is arsenic in the water, it would show up on this report. Additionally, fluoride is added to tap water in most cities in the US. If there is arsenic in the water or if fluoride removal is desired, reverse osmosis water filtration is the way to go.

Enquiry Form